@article { author = {Samii Zafarghandi, M. and Abbasi, S. M.}, title = {Hot Deformation Behavior of Haynes 25 by the Hot Tensile Test}, journal = {Journal of Advanced Materials in Engineering (Esteghlal)}, volume = {38}, number = {2}, pages = {1-10}, year = {2022}, publisher = {Isfahan University of Technology}, issn = {2251-600X}, eissn = {2423-5733}, doi = {10.29252/jame.38.2.1}, abstract = {In the present work, hot tensile behavior of Haynes 25 Co-base alloy was investigated in the temperature range of 950-1200 ˚C and 0.1 s-1. Thermodynamic calculations showed that M23C6 and M6C carbides were stable below 1000 ˚C and above 1050 ˚C, respectively. Stress-strain curves also indicated an unusual trend of strain fracture. It was observed that with increasing temperature from 950 to 1050 ˚C, the fracture strain was decreased, while it was raised above 1050 ˚C again. Increasing the volume fraction of M6C carbide rich in Tungsten resulted in the loss of ductility. Also, microstructural evaluations showed dynamic recrystallization (DRX) grains were nucleated and growth was around carbides and the initial grains at 1150 ˚C. Occurrence of DRX led to the improvement of ductility via grain refinement mechanism, so this alloy had the highest level of ductility at 1150 ˚C}, keywords = {Superalloy,Hot deformation,Carbide,Ductility,Dynamic recrystallization}, title_fa = {بررسی رفتار تغییرشکل گرم سوپرآلیاژ Haynes 25 از طریق آزمایش کشش گرم}, abstract_fa = {در این پژوهش، رفتار تغییر شکل­ سوپرآلیاژ پایه کبالت Haynes 25 در محدوده دمایی 1200-950 درجه سانتی‌گراد از طریق آزمایش کشش گرم در نرخ کرنش 1/0 بر ثانیه بررسی می‌شود. بررسی‌های ترمودینامیکی نشان داد که دو نوع کاربید M23C6 و M6C به‌ترتیب در محدوده دمایی زیر 1000 درجه سانتی‌گراد و بالای 1050 درجه سانتی‌گراد در آلیاژ Haynes 25 پایدار هستند. منحنی­های تنش- کرنش حاکی از یک روند غیرعادی میزان کرنش شکست برای آلیاژ گفته شده بود، بدین ترتیب که با افزایش دما از 950 به 1050 درجه سانتی‌گراد کرنش شکست کاهش و با افزایش مجدد دما افزایش یافت. ملاحظه شد که در محدوده دمایی حدود 1050 درجه سانتی‌گراد افزایش کسرحجمی کاربیدهای M6C غنی از تنگستن، سبب کاهش میزان انعطاف­پذیری آلیاژ می­شود. همچنین بررسی­ های ریزساختاری نشان داد که در دمای 1150 درجه سانتی‌گراد دانه ­های تبلور مجدد دینامیکی در اطراف کاربیدها و مرزهای اولیه جوانه ­زده و رشد کرده­اند. وقوع تبلور مجدد دینامیکی سبب بهبود انعطاف­ پذیری از طریق مکانیزم ریزدانه ­سازی می­ شود. بنابراین دمای 1150 درجه سانتی‌گراد بالاترین میزان انعطاف­پذیری را نسبت به دیگر دماها از خود نشان داد.}, keywords_fa = {سوپرآلیاژ,تغییر شکل گرم,کاربید,انعطاف‌پذیری,تبلور مجدد دینامیکی}, url = {https://jame.iut.ac.ir/article_2483.html}, eprint = {https://jame.iut.ac.ir/article_2483_52ee071d8a78c06d12c94e9e410859f6.pdf} }