@article { author = {Ghasemian Malakshah, M. and Ashrafizadeh, F. and Eslami, A. and Fadaeifard, F.}, title = {Corrosion Fatigue of 17-4pH Stainless Steel in a Simulated Sea Water Solution}, journal = {Journal of Advanced Materials in Engineering (Esteghlal)}, volume = {38}, number = {2}, pages = {69-81}, year = {2022}, publisher = {Isfahan University of Technology}, issn = {2251-600X}, eissn = {2423-5733}, doi = {10.29252/jame.38.2.69}, abstract = {Since martensitic precipitation hardened 17-4pH stainless steel has been widely used in corrosive environments, evaluation of its corrosion fatigue behavior is important. In this research, after microstructural studies, mechanical, corrosion, fatigue and corrosion fatigue tests were performed on 17-4pH specimens. Fatigue and corrosion fatigue tests were carried out at the  stress ratio of -1 and the  stress frequency of 0.42 Hz (to increase the effect of corrosive solution), and corrosion fatigue tests were conducted in 3.5% NaCl solution, an  environment similar to corrosive sea water. Fatigue limit of 17-4pH stainless steel was 700 MPa in air and 415 MPa in corrosive environment. Comparing the S-N curves of this alloy at the optimal heat treatment cycle in two modes of fatigue and corrosion fatigue revealed the reduction of fatigue limit up to 40 % in the presence of corrosive environment. This reduction was due to the effect of observed corrosion pits on the surface and Damaged passive layer.}, keywords = {Optimal heat cycle,Corrosion fatigue,Precipitation Hardenable Stainless Steel,S-N Curve}, title_fa = {خوردگی خستگی فولاد زنگ‌نزن pH4-17 در محیط شبیه‌سازی شده آب دریا}, abstract_fa = {از آنجایی که فولاد زنگ­نزن رسوب سخت شونده مارتنزیتی pH4-17 کاربرد وسیعی در محیط­ های خورنده دارد، مطالعه رفتار خوردگی خستگی این آلیاژ حائز اهمیت است. در این پژوهش، پس از مطالعات ریزساختاری، آزمون­ های مکانیکی، خوردگی، خستگی و خوردگی خستگی روی نمونه­ های pH4-17 در چرخه بهینه حرارتی انجام شده است. آزمون­ های خستگی و خوردگی خستگی در نسبت تنش 1- و فرکانس اعمال تنش 42/0 هرتز (جهت افزایش تأثیر محلول خورنده) و آزمون خوردگی خستگی در حضور محلول خورنده 5/3 درصد وزنی NaCl  مشابه محیط خورنده آب دریا انجام گرفت. حد خستگی آلیاژpH 4-17 در هوا 700 مگاپاسکال و در محیط خورنده 415 مگاپاسکال است. مقایسه نمودار S-N این آلیاژ در چرخه بهینه حرارتی در دو حالت خستگی و خوردگی خستگی، کاهش حد خستگی در حدود 40 درصد را در محیط خورنده مشخص کرد. بررسی­ ها نشان داد این امر ناشی از تأثیر منفی حفرات خوردگی مشاهده شده در سطح و آسیب دیدن لایه رویین تشکیل شده بر سطح این فولاد زنگ نزن است.}, keywords_fa = {چرخه بهینه حرارتی,خوردگی خستگی,فولاد زنگ‌نزن رسوب سخت شونده,نمودار S-N}, url = {https://jame.iut.ac.ir/article_2488.html}, eprint = {https://jame.iut.ac.ir/article_2488_6535a26af72fb45f366e39eff5f217c7.pdf} }