دانشگاه صنعتی اصفهانمواد پیشرفته در مهندسی2251-600X37420221231Grain Growth Kinetics of Magnesium Alloys Containing Aluminum and Rare-Earth Element Gadoliniumسینتیک رشد دانه در آلیاژهای منیزیم حاوی آلومینیوم و عنصر نادر خاکی گادولینیم111246710.29252/jame.37.4.1FAبیتاپوربهاریدانشگاه تهراندانشکده مهندسی متالورژی و مواد، دانشکده فنی، دانشگاه تهرانحامدمیرزادهدانشکده مهندسی متالورژی و مواد، دانشکده فنی، دانشگاه تهرانمسعودامامیدانشکده مهندسی متالورژی و مواد، دانشکده فنی، دانشگاه تهرانJournal Article20221231Microstructural evolutions during the high-temperature annealing of Mg alloys containing Al and Gd and after the extrusion process were evaluated and compared to those of the AZ61 alloy. It was revealed that during exposure at the elevated temperatures, the presence of (Mg,Al)3Gd phase, in the form of fine and dispersed particles in the matrix after the extrusion process, could be favorable for the inhibition of grain growth. It was also found that the Al2Gd particles could not effectively retard the coarsening of grains. On the other hand, the grain growth of AZ61 alloy was found to be problematic, which was related to the dissolution of the Mg17Al12 intermetallic phase at temperatures higher than 300°C. In the Mg alloys containing both Al and Gd elements, the increased thermal stability was observed, which was ascribed to the rise of the melting temperature. Finally, some abnormal grain growth was observed in the presence of Al2Gd phase, which was attributed to the nonuniform pinning of grain boundaries by this intermetallic compound.
تحولات ریزساختاری در حین عملیات آنیل دمای بالا برای آلیاژهای منیزیم حاوی آلومینیوم و گادولینیمپس از فرایند اکستروژن مورد ارزیابی قرار گرفت و با آلیاژ 61AZ مقایسه شد. با قرارگیری آلیاژها در دمای بالا مشخص شد که حضور فاز Gdز3(Mg,Al) که پس از اکستروژن بهشکل ذرات ریز و پراکنده در ریزساختار قرار میگیرد اثر مثبتی بر جلوگیری از رشد دانهها دارد. همچنین مشخص شد که ذرات Gd2 Al نمیتوانند به شکل مؤثری جلوی رشد دانه را بگیرند. از طرف دیگر، رشد دانه در آلیاژ 61AZ بهعنوان یک مشکل جدی مطرح شد که میتواند بهدلیل حل شدن ذرات بین فلزی 12Al 17Mg در دماهای بالاتر از 300 درجه سانتیگراد باشد. در آلیاژهای منیزیم حاوی آلومینیوم و گادولینیم، بهبود پایداری آلیاژ در دمای بالا دیده شد که به افزایش دمای ذوب نسبت داده شد. درنهایت، رشد دانه غیریکنواخت در حضور ذرات Al2Gd مشاهده شد که به اثر پینکنندگی غیریکنواخت مرزدانهها توسط این ترکیب بین فلزی مرتبط شد.https://jame.iut.ac.ir/article_2467_f1010a52dbd010d5162a1378ce831238.pdfدانشگاه صنعتی اصفهانمواد پیشرفته در مهندسی2251-600X37420221231The Effect of Rheological Parameters on the Behavior of Silicon Nitride-Starch Slurry Used in Gelcasting Porous Silicon Nitrideتأثیر پارامترهای مؤثر بر رفتار جریانی دوغاب نیترید سیلیسیم- نشاسته بهمنظور ساخت قطعات متخلخل نیترید سیلیسیمی بهروش ریختهگری ژلی1323246810.29252/jame.37.4.13FAمهرانحق شناس گرگانیدانشکده مهندسی مواد و متالورژی، دانشگاه علم و صنعت ایرانمحمدمیرکاظمیدانشکده مهندسی مواد و متالورژی، دانشگاه علم و صنعت ایرانفرهادگلستانی فرددانشکده مهندسی مواد و متالورژی، دانشگاه علم و صنعت ایرانJournal Article20221231In this research, the rheological behavior and stability of suspensions containing Si3N4, Al2O3, Y2O3 and starch were investigated in order to use them in the starch consolidation casting of porous silicon nitride. Dolapix CE64 was used as the dispersant. Then, the effect of some parameters such as Si3N4 surface oxidation, dispersant content, solid loading and starch content on the viscosity and rheological behavior of Si3N4-starch slurry was determined. Surface oxidation of Si3N4 powder at 800°C for 2 hours reduced the viscosity of the slurry, effectively. The best dispersant content was 0.4 wt. %, relative to ceramic powders. Slurries containing 30 to 40 vol. % and 7.5 to 25 vol. % starch, relative to total solid loading, had the suitable viscosity and the sufficient stability for casting by the starch consolidation method.در این پژوهش، رفتار جریانی و پایداری دوغاب متشکل از نیترید سیلیسیم، آلومینا، ایتریا و نشاسته، با هدف توسعه روش ریختهگری ژلی با استفاده از نشاسته برای ساخت قطعات نیترید سیلیسیمی متخلخل بررسی شده است. برای پایدارسازی دوغاب، از پراکندهساز دولاپیکس سی ای 64 (Dolapix CE64) استفاده شد. تأثیر عواملی چون اکسید کردن سطحی پودر نیترید سیلیسیم، مقدار پراکندهساز، میزان بار جامد و مقدار نشاسته بر رفتار جریانی و گرانروی دوغابهای متشکل از نیترید سیلیسیم و نشاسته بررسی شد تا دوغابی پایدار و با گرانروی مناسب بهدست آید. اکسید کردن سطحی پودر نیترید سیلیسیم در دمای 800 درجه سانتیگراد بهمدت دو ساعت باعث کاهش گرانروی دوغاب شد. بهترین حالت مقدار پراکندهساز 4/0 درصد وزنی نسبت به بار جامد بهدست آمد. همچنین دوغابهایی با بار جامد 30 تا 40 درصد حجمی و مقدار نشاسته 5/7 تا 25 درصد حجمی نسبت به بار جامد دارای گرانروی مناسب و پایداری کافی برای ریختهگری بودند.https://jame.iut.ac.ir/article_2468_2b43fe1e07014c1f274cb6e82cd2804e.pdfدانشگاه صنعتی اصفهانمواد پیشرفته در مهندسی2251-600X37420221231An Investigation Into the Properties of MoS2-Cr Coatings Produced by DC Magnetron Sputteringبررسی خواص پوشش MoS2-Cr ایجاد شده توسط فرایند پراکنش مگنترونی DC2541246910.29252/jame.37.4.25FAمهدیاکبرزاده1. دانشکده مهندسی مواد و متالوژی، دانشگاه شهید باهنر کرمانمرتضیزند رحیمی1. دانشکده مهندسی مواد و متالوژی، دانشگاه شهید باهنر کرماناحسانمرادپور2. دانشکده مهندسی مواد، دانشگاه تربیت مدرسJournal Article20221231Molybdenum disulfide (MoS2) is one of the most widely used solid lubricants. In this study, MoS2-Cr composite coatings were deposited onto AISI 1045 steel substrates by direct-current magnetron sputtering. The MoS2/Cr ratio in the coatings was controlled by sputtering the composite targets. The coatings were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), and nano-indentation and nano-scratch techniques. The tribological behavior of the coatings was investigated using the pin-on-disc test at room temperature. The results showed that the thickness and the hardness of the coating were 6 µmand 850-1300 HV, respectively. The degree of the crystallization of the composite coatings was enhanced with increasing the Cr contents. The incorporation of Cr into MoSx coatings resulted in the considerable improvement of coating adhesion and hardness. The optimum doping level for MoS2-Cr coatings to show the best tribological propertie was 13 atomic percent. The main wear mechanisms of the coating were delamination, tribochemical and abrasive micro cracking- دی سولفید مولیبدن (MoS2) یکی از رایجترین پوششهای روانکار جامد است. در این تحقیق پوششهای کامپوزیتی MoS2-Cr بهروش کندوپاش مغناطیسی جریان مستقیم، روی فولاد AISI1045 عمال شد. نسبت کروم در پوشش با استفاده از تارگتهای مختلف کنترل شد. پوششها با استفاده از پراش پرتو ایکس (XRD)، میکروسکوپ الکترونی روبشی (SEM)، طیفسنجی پراش انرژی پرتو ایکس (EDX) و نانوفرورونده و نانوخراش مشخصهیابی شد. نتایج نشان داد که ضخامت و سختی پوششهای ایجاد شده بهترتیب 6 میکرومتر و 1300-850 ویکرز بود. حضور کروم در پوشش MoSx باعث بهبود چسبندگی و افزایش سختی پوشش میشود. میزان بلورینگی ساختار با افزایش میزان کروم کاهش مییابد. مقدار بهینه افزودن کروم برای ایجاد بهترین خواص سایشی پوششهای MoS2-Cr، 13 درصد اتمی تعیین شد. سایش ورقهای و تریبوشیمی و خراشان با مکانیزم خیش ریز بهعنوان مهمترین مکانیزمهای حاکم در سایش پوشش تعیین شد.https://jame.iut.ac.ir/article_2469_c869930097693f213721e0e4b1988d0a.pdfدانشگاه صنعتی اصفهانمواد پیشرفته در مهندسی2251-600X37420221231The Effect of Boron and Zirconium on the Microstructure and Mechanical Properties of Cast Fe3Al-Based Alloysاثر بور و زیرکونیوم بر ریزساختار و خواص مکانیکی آلیاژهای ریختگی آلومیناید آهن Fe3Al4357247010.29252/jame.37.4.43FAمحمدرجبی1. دانشکده مهندسی مواد و متالورژی، دانشگاه علم و صنعت ایرانمحمدشاهمیری1. دانشکده مهندسی مواد و متالورژی، دانشگاه علم و صنعت ایرانمحسنقنبری2. دانشکده فنی، دانشگاه آزاد اسلامی واحد کرجJournal Article20221231In this study, the effects of boron (B) and zirconium (Zr) on the microstructure and mechanical properties of Fe3Al-based alloys were investigated. Cylindrical samples were produced using a vacuum induction melting furnace (VIM); consequently, the melt was cast into a metallic mold. The microstructure, phase identification, tensile and compressive mechanical properties and fractography of the samples were investigated. Upon microstructural observation, it was found that the alloys microstucture was denderitic and the precipitated phases were mostly present between interdendritic regions. Addition of B and Zr to the alloys resulted in the formation of boride precipitates and Laves phases. The results, therefore, showed that Zr had the most pronounced effect on the mechanical properties because of the formation of Laves phases. Fractographic studies of alloys also revealed that the brittle fracture was dominant between the samples.در این پژوهش، اثر بور و زیرکونیوم بر ریزساختار و خواص مکانیکی آلیاژهای بر پایه Fe3Alمورد مطالعه قرار گرفته است. بهمنظورآلیاژسازی از کوره القایی تحت خلأ استفاده شد و ریختهگری در قالب فلزی صورت گرفت. بررسیهای ریزساختاری، فازشناسی، خواص مکانیکی فشاری، کششی و همچنین شکستنگاری روی نمونهها انجام گرفت. بر اساس مشاهدات ریزساختاری، ریزساختار آلیاژها بهصورت دندریتی است و فازهای رسوبی بهطور عمومی در مناطق بین دندریتی حضور دارند. افزودن بور و زیرکونیوم موجب تشکیل فازهای رسوبی بورایدی ولاوه در آلیاژ میشود. بررسی تأثیر عناصرآلیاژی افزوده شده به آلیاژ نشان میدهد، زیرکونیوم بهعلت تشکیل فازهای لاوه بیشترین تأثیر را بر بهبود خواص مکانیکی آلیاژها دارد. بررسی مکانیزم شکست در بین آلیاژها، حاکی از شکست ترد در آنها است..https://jame.iut.ac.ir/article_2470_c9906fa09ea45c8039654182e480218b.pdfدانشگاه صنعتی اصفهانمواد پیشرفته در مهندسی2251-600X37420221231The Effect of Boron Addition on the Microstructure, Hardness and Characteristic Temperatures of Cu-12Al-4Ni Memory Alloy Prepared by Mechanical Alloying, Pressing and Rollingاثر افزودن بور بر ساختار، سختی و دماهای استحاله آلیاژ حافظهدار Cu-12Al-4Ni تهیه شده به روش آلیاژسازی مکانیکی، پرس و نورد5972247110.29252/jame.37.4.59FAزینبجراحی1. دانشکده مهندسی مواد و متالورژی، پردیس دانشکدههای فنی، دانشگاه تهرانشهرامرایگان1. دانشکده مهندسی مواد و متالورژی، پردیس دانشکدههای فنی، دانشگاه تهرانمهدیپورعبدلی2. گروه مهندسی متالورژی و مواد، دانشگاه صنعتی همدانJournal Article20221231In this study, boron containing Cu-12wt%Al-4wt%Ni shape memory alloy was prepared by mechanical alloying, pressing and rolling. In this regard, 20 and 40 hour-milled powder was compacted and changed to the bulk alloy by cold pressing, sintering, rolling, heat treatment and quenching. Phase structure, micro-structure, micro-hardness, and transformation temperatures of the prepared samples were studied. It was found that increasing the milling time from 20 to 40 hours led to the rise of the starting temperature of martensite transformation (Ms) from 254 to 264°C. Also, the results showed that adding 0.5 wt.% B decreased the Ms temperature to 211°C and enhanced the micro-hardness from 154 (for the sample without B) to 193 vickers. These alternations were attributed to the fine structure caused by Boron rich precipitations. Moreover, two martenistic transformations with different structures were formed due to the non-homogeneity of the Al concentration in the matrix, which appeared in the form of two different transformation temperatures (Ms) in the Differential Scanning Calorimetry curves.در این پژوهش، ساخت آلیاژ حافظهدار Cu-12wt%Al-4wt%Ni حاوی بور بهروش آلیاژسازی مکانیکی، پرس و نورد مورد بررسی قرار گرفت. برای تهیه نمونه بالک از پودرهای آلیاژسازی مکانیکی شده بهمدت 20 و 40 ساعت، از روشهای پرس سرد، تفجوشی، نورد، عملیات حرارتی و کوئنچ استفاده شد. ساختار فازی، میکروساختار، میکروسختی و دمای استحاله نمونههای حاصل مورد مطالعه قرار گرفت. مشخص شد که با افزایش زمان آسیاکاری از 20 به 40 ساعت دماهای شروع استحاله مارتنزیتی از 254 به 264 درجه سانتیگراد افزایش پیدا میکند. همچنین، نتایج نشان داد که افزودن عنصر بور به مقدار 5/0 درصد وزنی باعث افت دمای استحاله به 211 درجه سانتیگراد و افزایش میکروسختی از مقدار 154 به 193 ویکرز میشود که علت آن به ریزدانه شدن در اثر ظهور رسوبات غنی از بور نسبت داده شد. بهدلیل ناهمگنی نسبی در غلظت آلومینیوم در زمینه و تشکیل مارتنزیت با ساختار متفاوت، استحاله دو مرحلهای بروز کرد که در نمودار آزمون گرماسنجی تفاضلی روبشی DSCبهصورت دو پیک مجزا ظاهر شد.https://jame.iut.ac.ir/article_2471_c03e5765a9076e79f7cc11bfd4570296.pdfدانشگاه صنعتی اصفهانمواد پیشرفته در مهندسی2251-600X37420221231Modification of Superhydrophilic, Anti-bacterial Polyurethane Polymer with TiO2 Nanoparticles for Medical Devicesاصلاح ابرآبدوست و آنتی باکتریال پلیمر پلیاورتان بهکمک نانوذرات دیاکسید تیتانیوم بهمنظور استفاده در ابزار پزشکی7389247210.29252/jame.37.4.73FAامیررزمجودانشکده علوم و فناوری های نوین، دانشگاه اصفهانفاطمهنوری صفادانشکده علوم و فناوری های نوین، دانشگاه اصفهانناهیدامامیدانشکده علوم و فناوری های نوین، دانشگاه اصفهانJournal Article20221231Polyurethane polymer plays an important role in health care, and it is widely used in medical devices and instruments. However, the low biocompatibility and biofilm formation on the surface can be regarded as a challenging issue. Engineering the wetting capability of the surface is an effective way to increase the biodegradability of polymer surfaces with sufficient bulk properties. In this study, the surface modification of polyurethane sheets by a thin layer of polyethylene glycol and trapping of titanium dioxide nanoparticles were carried out by means of physical and chemical changes on the surface to enhance the biocompatibility. The physicochemical properties of the modified surfaces were determined using fourier-transform infrared (FTIR) spectroscopy , scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and contact angle and free surface energy measurement. The biocompatibility of the modified levels was evaluated using the MTT toxicity test on cervical cancer cells (HeLA), bacterial adhesion, biofilm formation, and the protein absorption assay by the Bradford method. A thin, autoclave able and inexpensive thin layer with a solid and stable roughening structure was created covalently on the surface of the polyurethane plates for biological and medical applications. The results, therefore, showed that apart from antibacterial activity, the modified sample also had the ability to reduce the biofilm formation, such that the maximum biofilm attachment inhibition in the first 24 hours was 94% higher than that of the modified sample.پلیمر پلیاورتان نقش مهمی در مراقبتهای بهداشتی دارد و بهطور گسترده در دستگاهها و ابزارهای پزشکی مورد استفاده قرار میگیرد. با این حال، هنوز زیستسازگاری پایین و تشکیل بیوفیلم در سطح آن، موضوعی چالش برانگیز است. اصلاح ترشوندگی سطح روشی مؤثر برای افزایش زیستسازگاری سطح پلیمرهای دارای خواص توده مطلوب است. در این مطالعه، اصلاح سطح صفحات پلیاورتان توسط لایه نازک پلیاتیلن گلیکول و به دام افتادن نانوذرات دیاکسید تیتانیوم در پلیمر بهکمک تغییر ساختار فیزیکی و شیمیایی سطح بهمنظور افزایش زیستسازگاری انجام گرفت. خواص فیزیکوشیمیایی سطوح اصلاح شده با استفاده از طیفسنجی تبدیل فوریه مادون قرمز (FTIR)، میکروسکوپ الکترونی روبشی (SEM)، آنالیز پراش انرژی پرتو ایکس(EDX) و اندازهگیری زاویه تماس و انرژی آزاد سطح مشخص شد. زیستسازگاری سطوح اصلاح شده با استفاده از آزمون سمیت MTT بر سلولهای سرطانی دهانه رحم، چسبندگی باکتریاییها و بررسی تشکیل بیوفیلم و سنجش جذب پروتئین بهروش برادفورد مورد بررسی قرار گرفت. یک لایه نازک قابل اتوکلاو و ارزان با ساختار دارای زبری چندگانه و پایدار بهطور کووالان روی سطح صفحات پلیاورتان برای کاربردهای زیستی و پزشکی ایجاد شد. نتایج نشان میدهد که بهغیر از فعالیتهای ضد باکتریایی، نمونه اصلاح شده نیز توانایی کاهش تشکیل بیوفیلم را دارد بهطوریکه حداکثر مهار بیوفیلم در 24 ساعت اول 94 درصد بیشتر از نمونه اصلاح نشده است.https://jame.iut.ac.ir/article_2472_149755dec1b332456b8402b655ea364b.pdfدانشگاه صنعتی اصفهانمواد پیشرفته در مهندسی2251-600X37420221231Determination of the Modified Hall-Petch Equation Constants and the Relationship Between the Microstructure and Mechanical Properties of AS7U3G Alloyتعیین ثابتهای رابطه هال- پچ اصلاح شده و ارتباط خواص مکانیکی با ریزساختار آلیاژ AS7U3G91100247310.29252/jame.37.4.91FAمیثملشنی زند1. دانشکده مهندسی مواد و متالورژی، دانشگاه صنعتی اصفهانبهزادنیرومند1. دانشکده مهندسی مواد و متالورژی، دانشگاه صنعتی اصفهانبهزادنیرومند1. دانشکده مهندسی مواد و متالورژی، دانشگاه صنعتی اصفهانعلیمالکی2. دانشکده مهندسی مکانیک، دانشگاه صنعتی اصفهانJournal Article20221231Mechanical properties of the alloys are a strong function of the average silicon particles size and the secondary dendrite arm spacing (SDAS). Modified Hall-Petch equation expresses the effects of these two microstructural parameters on the yield strength and ultimate tensile strength of the Al-Si based alloys. These microstructural parameters depen on parameters such as chemical composition, cooling rate and melt treatment. In this study, the effect of cooling rate on the equation constants of the alloy were determined. For this purpose, the alloy was poured at 750 °C in three different molds including a sand mold, a preheated steel mold, and a water cooled steel mold. The Thermal and microstructural analysis showed that the cooling rate in the metal mold was 15.7 times higher than that of the sand mold, which resulted in a decrease of the SDAS from 54 micrometers to 17 micrometers. It was also found that by reducing the SDAS from 45 micrometers to 17 micrometers, the yield strength and tensile strength were increased by 16.5% and 6.5%, respectively. The modified Hall-Petch equation constants and the microstructure-mechanical properties relationships were then established by the microstructural and tensile test studies.خواص مکانیکی آلیاژهای آلومینیوم- سیلیسیم هیپویوتکتیک بهشدت تابع ابعاد تیغههای سیلیسیم یوتکتیکی و فاصله بین بازوهای ثانویه دندریتی است. رابطه هال- پچ اصلاح شده اثر این دو متغیر ریزساختاری بر استحکام تسلیم و استحکام کششی آلیاژهای پایه آلومینیوم- سیلیسیم را نشان میدهد. این دو متغیر ریزساختاری به متغیرهایی همچون ترکیب شیمیایی، سرعت سرد شدن و عملیات کیفی مذاب بستگی دارند. در این پژوهش اثر سرعت سرد شدن بر مشخصات ریزساختاری و خواص مکانیکی آلیاژ AS7U3G بررسی شده، ثوابت رابطه هال- پچ اصلاح شده برای این آلیاژ بهدست آمد. به این منظور آلیاژ از دمای 750 درجه سانتیگراد در قالبهای ماسهای، فلزی پیشگرم شده و فلزی آبگرد ریخته شد. بررسیهای آنالیز حرارتی و متالوگرافی نشان داد که سرعت سرد شدن در قالب فلزی آبگرد 7/15 برابر بیشتر از قالب ماسهای بوده که درنتیجه باعث کاهش فاصله میانگین بازوهای ثانویه دندریتی از 54 میکرومتر به 17 میکرومتر شد. همچنین مشخص شد که با کاهش فاصله بازوهای ثانویه دندریتی از 45 میکرومتر به 17 میکرومتر استحکام تسلیم و استحکام کششی بهترتیب 5/16 و 5/6 درصد افزایش مییابد. در ادامه با بررسیهای متالوگرافی و انجام آزمونهای کشش، ثابتهای رابطه هال- پچ اصلاح شده و ارتباط خواص کششی با ریزساختار آلیاژ بهدست آمد.https://jame.iut.ac.ir/article_2473_7d3875256d0a3dc84e5a26524136f3c6.pdfدانشگاه صنعتی اصفهانمواد پیشرفته در مهندسی2251-600X37420221231Fabrication and Characterization of an Optical Nano-hybrid Sol-gel Derived Thin Film on the PMMA Substrateلایه نشانی لایه نازک نانوهیبریدی TEOS-GPTMS روی زیرلایه پلیمتیل متاکریلات101112247410.29252/jame.37.4.101FAمجتبیحاجفرجزادهدانشکده مهندسی مواد، دانشگاه صنعتی مالک اشتر، شاهینشهراکبراسحاقیدانشکده مهندسی مواد، دانشگاه صنعتی مالک اشتر، شاهینشهرعباسعلیآقائیدانشکده مهندسی مواد، دانشگاه صنعتی مالک اشتر، شاهینشهرJournal Article20221231A TEOS-GPTMS nano-hybrid thin film was deposited on the polymethyl methacrylate (PMMA) substrate by a sol-gel dip coating method. Morphology, roughness and surface chemical bonding of the thin films were evaluated by X-ray diffraction (XRD), field emission scanning electron microscopy(FE-SEM), atomic force microscopy, and Fourier transform infrared spectroscopy methods, respectively. UV-vis spectrophotometer was used to measure the transmittance spectra of the samples. Also, the adhesion and hardness of the coatings were investigated using pencil hardness the adhesion tape test and the test, respectively. XRD results proved that the thin film had an amorphous structure. Also, FE-SEM images indicated that addition of GPTMS to the TEOS yielded a crack-free thin film. Based on the UV-vis spectroscopy results, the transmittance of the polymer substrate in the visible region was increased by the deposition of the nano-hybrid coating. Moreover, the hardness of the PMMA substrate was increased from 3H to 6H by the deposition of the nano-hybrid thin film. Also, tape test confirmed the high adhesion of the nano-hybrid thin film on the PMMA substrate. Consequently, the transparent organic-inorganic GPTMS-TEOS hybrid coating can be used as a scratch resistant coating on the PMMA substrate.لایه نازک نانوهیبریدی تترا اتیل اورتوسیلیکات- تریگلیسیدوکسییپروپیل تریمتوکسیسیلان روی زیرلایه پلیمتیل متاکریلات بهروش سل- ژل غوطهوری اعمال شد. آزمونهای پراشسنجی پرتو ایکس، طیفسنجی تبدیل فوریه مادون قرمز با تکنیک بازتاب کلی تضعیف شده، میکروسکوپی الکترونی روبشی گسیل میدانی و میکروسکوپی نیروی اتمی بهترتیب بهمنظور بررسی ساختار، پیوندهای سطحی، مورفولوژی و زبری لایه نازک صورت گرفت. طیفسنجی نور مرئی- فرابنفش بهمنظور اندازهگیری طیف عبور نمونهها انجام شد. همچنین چسبندگی و سختی پوشش بهترتیب توسط آزمونهای نوار و مداد ارزیابی شد. نتایج حاصل از آنالیز پراشسنجی پرتو ایکس، تشکیل پوششی با ساختار آمورف را اثبات کرد. همچنین تصاویر میکروسکوپی الکترونی روبشی گسیل میدانی مشخص کرد که با اضافه کردن GPTMS به سل TEOS فیلمی عاری از ترک ایجاد خواهد شد. همچنین بر اساس نتایج طیفسنجی نور مرئی- فرابنفش، اعمال لایه نازک نانوهیبریدی افزایش میزان عبور را در ناحیه مرئی نسبت به زیرلایه پلیمتیل متاکریلات بههمراه خواهد داشت. در ضمن، آزمون مداد نشان داد که با اعمال لایه نازک نانوهیبریدی روی زیرلایه پلیمری سختی از H3 به H6 افزایش مییابد. از طرفی آزمون نوار چسبندگی بالای لایه نازک نانوهیبریدی را به زیرلایه پلیمتیل متاکریلات اثبات کرد. درنتیجه پوشش شفاف هیبریدی آلی- معدنی GPTMS-TEOS، میتواند بهعنوان پوشش ضدخش روی زیرلایه پلیمری پلیمتیل متاکریلات استفاده شود.https://jame.iut.ac.ir/article_2474_d6854b3ff91e7caea9758a5f20723fac.pdf