A Comparative Study of the Addition Effect of Diopside and Silica Sulfuric Acid Nanoparticles on Mechanical Properties of Glass Ionomer Cements

Authors

1 1. Department of Materials Engineering, University of Shahrekord, Shahrekord, Iran

2 2. Department of Chemistry, Science Faculty, Islamic Azad University, Shahrekord Branch, Shahrekord, Iran

Abstract

The aim of the present study is to study the effects of adding  diopside (CaMgSi2O6) as well as silica sulfuric acid nanoparticles to ceramic part of glass ionomer cement (GIC) in order to improve its mechanical properties. To do this, firstly, diopside (DIO) nanoparticles with chemical formula of CaMgSi2O6 were synthesized using sol-gel process and then, the structural and morphological properties of synthesized diopside nanoparticles were investigated. The results of scanning electron microscopy (SEM) and particle size analyzing (PSA) confirmed that synthesized diopside are nanoparticles and agglomerated. Besides, the result of X-ray diffraction (XRD) analyses approved the purity of diopside nanoparticles compounds. Silica sulfuric acid (SSA) nanoparticles are also prepared by chemical modification of silica nanoparticles by means of chlorosulfonic acid. Fourier transform infrared spectroscopy (FTIR) technique was used to find about the presence of the (SO3H) groups on the surface of silica sulfuric acid nanoparticles. Furthermore, various amounts (0.1, 3 and 5 wt.%) of diopside and silica sulfuric acid nanoparticles were added to the ceramic part of GIC (Fuji II GIC commercial type) to produce glass ionomer cement nanocomposites. The mechanical properties of the produced nanocomposites were measured using the compressive strength, three-point flexural strength and diametral tensile strength methods. Fourier transform infrared spectroscopy technique confirmed the presence of the (SO3H) groups on the surface of silica nanoparticles. The compressive strength, three-point flexural strength and diametral tensile strength were 42.5, 15.4 and 6 MPa, respectively, without addition. Although adding 1% silica solfonic acid improved nanocomposite mchanical properties by almost 122%, but maximum increase in nanocomposite mechanical properties was observed in the nanocomposites with 3% diposid, in which 160% increase was seen in the mechanical properties.

Keywords

References

1. Khan, A.S., Khan, M. and Rehma, I., “Nanoparticles, Properties, and Applications in Glass Ionomer Cements”, Nanobiomaterials Clinical Dentistry,
Vol. 5, pp. 94-97, 2013.
2. Moshaverinia, A., Ansari, S., Moshaverinia, M., Roohpour, N., Darr, J.A. and Rehman, I., “Effects of Incorporation of Hydroxyapatiteand Fluoroapatitenanobioceramics into Conventional Glass Ionomer Cements (GIC)”, ActaBiomaterials, Vol. 4, pp. 432-440, 2008.
3. Wilson, A.D. and Kent, B.E., “A New Translucent Cement for Density of the Glass Ionomer Cement”, British Dental Journal, Vol. 132, pp. 133-135, 1972.
4. Schmitt, W., Purrman, R., Jochum, P. and Gasser, O., “Mixing Component for Dental Glass Ionomer cements”, US Patent, No. 4360605, 1982.
5. Urpo, H.Y., Narhi, M. and Narhi, T., “Compound Changes and Tooth Mineralization Effects of Glass Ionomer Cements Containing Bioactive Glass (S53P4), an in vivostudy”, Biomaterials, Vol. 26,
pp. 5934-5941, 2005.
6. Xie, D., Brantley, W.A., Culbertson, B.M. and Wang, G., “Mechanical Properties and Microstructures of Glass-Ionomer Cements”, Dental Materials, Vol. 16, pp. 129–138, 2000.
7. Nonami, T. and Tsutsumi, S., “Study of Diopside Ceramics for Biomaterials”, Journal of Matererials. Science: Materials in Medicine, Vol. 10, pp. 475-479, 1999.
8. Wu, C. and Chang, J., “A Review of Bioactive Silicate Ceramics”, Biomedical Materials, Vol. 8,
pp. 1-12, 2013.
9. Iwata, N.Y., Lee, G.H., Tsunakawa, S., Tokuoka, Y. and Kawashima, N., “Preparation of Diopside with Apatite-Forming Ability by Sol–Gel Process using Metal Alkoxide and Metal Salts”, Colloids Surface B, Vol. 33, pp. 1-6, 2004.
10. Zhang, M., Liu, C., Zhang, X., Pan, S. and Xu, Y., “Al2O3/Diopside Ceramic Composites and their Behavior in Simulated Body Fluid”, Ceramic International, Vol. 36, pp. 2505-2509, 2010.
11. Zhang, M., Liu, C., Sun, J. and Zhang, X., “Hydroxyapatite/Diopside Ceramic Composites and their Behaviour in Simulated Body Fluid”, Ceramic International, Vol. 37, pp. 2025–2029, 2011.
12. Xihua, Z., Changxia, L., Musen, L., Yunqiang, B. and Junlong, S., “Fabrication of Hydroxyapatite /Diopside/Alumina Composites by Hot-Press Sintering process”, Ceramic International, Vol. 35, pp. 1969–1973, 2009.
13. Liu, C., Sun, J., and Xie, Z., “Microstructures and Sintering Kinetics of Pressureless Sintered Alumina Doped with Diopside and AlTiB”, Journal of Alloys and Compounds, Vol. 546, pp. 102-106, 2013.
14. Luhres A.K. and Geurtsen, W., “The Application of Silicones and Silicates in Dentistry: A Review”, in Biosilica in Evolution, Morphologenisis and Nanobiotechnology, Progress in Molecular and Subcellular Biotechnology, Muller W.E.G. and Grachev M.A. (eds), pp. 359-380, 2009.
15. Dastjerdi, R. and Montazer, M., “A Review on the Application of Inorganic Nano-Structured Materials in the Modification of Textiles: Focus on Anti-Microbial Properties”, Colloids and Surfaces,
Vol. 79, pp. 5-18, 2010.
16. Hobekast, L.V., Camacho, G.B. and Demarco, F.F., “Tensile Bond Strength and Flexural Modulus of Resin Cements– Influence of the Fracture Resistance of Teeth Restored with Ceramic Inlays”, Journal of Operative Dentistry, Vol. 32, pp. 488-495, 2007.
17. Elsaka, S.E., Hamouda, I.M. and Swain, M.V., “Titanium Dioxide Nanoparticles Addition to a conventionalglass-ionomer Restorative: Influence on Physical and Antibacterial Properties”, Journal of Dentistry, Vol. 39, pp. 589 – 598, 2011.
18. Gu, Y.W., Yap, A.U.J., Cheang, P. and Khor, K.A., ''Effects of Incorporation of HA/ZrO2 into Glass Ionomer Cement (GIC)'', Biomaterials, Vol. 26,
pp. 713–720, 2005.
19. Sayyedan, F.S., Fathi, M.H., Edris, H., Doostmohammadi, A. and Hanifi, A., “Effect of Forsterite Nanoparticles on Mechanical Properties of Glass Ionomer Cements”, Ceramic International, Vol. 40, pp. 10743–10748, 2014.
21. Torkian, L., Salehi, P., Dabiri, M. and Kharrazi, S., “Synthesis and Catalytic Applicationsof Sulfonic Acid Group–Functionalized-Nano and Microsilica Structures”, Synthetic Communications, Vol. 41,
pp. 2115-2122, 2012.
22. Razavi, M., Fathi M.H., Savabi O., Vashaee D. and Tayebi, L., “In Vitro Study of Nanostructured Diopside Coating on Mg Alloy Orthopedic Implants”, Materials Science and Engineering C., Vol.41, pp.168-177. 2014.
23. Rahman, I.A. and Padavettan, V.,” Synthesis of Silica Nanoparticles by Sol-Gel: Size-Dependent Properties, Surface Modification, and Applications in Silica-Polymer Nanocomposites- A Review”, Journal of Nanomaterials, Vol. 2012, pp. 1-15, 2012.
24. Patel, B.H., and Patel, P.N., “Synthesis and Characterization of Silica Nano-Particles by Acid Leachin Technique”, Research Journal of Chemical Science, Vol. 4, pp. 52-55, 2014.
25. Siddiqui, Z.N., Khan, K. and Ahmed, N., “Nano Fibrous Silica Sulphuric Acid as an Efficient Catalyst for the Synthesis of β- Enaminone”, Catalysis Letters, Vol. 144, pp.623-632, 2014.
26. Moshaverinia, A., Ansari, S., Movasaghi, Z., Billington, R.W., Darr, J.A. and Rehman, I.U., “Modification of Conventional Glass-Ionomer Cements with N-vinylpyrrolidone Containing Polyacids, Nano-Hydroxyandfluoroapatite to Improve Mechanical Properties”, Dental Materials, Vol. 24, pp. 1381-1390, 2008.
27. Sumit, G., Rajkamal, B. and Sampath, T.S., ''Effects of Nanocrystalline Calcium Deficient Hydroxyapatite Incorporation in Glass Ionomer Cements '', Journal of the Mechanical Behavior of Biomedical Materials, Vol. 7, pp. 69-76, 2012.
28. Rajabzadeh, G., Salehi, S., Nemati, A., Tavakoli, R. and Hashjin, M.S., “Enhancing Glass Ionomer Cement Features by Using the HA/YSZ Nanocomposite: A Feed Forward Neural Network Modeling”, Journal of the Mechanical Behavior of Biomedical Materials, Vol. 29, pp. 317-327, 2014.
29. Khademolhosseini, M.R., Barounian, M.H., Eskandari, A., Aminzare, M., Zahedi, A.M. and Ghahremani, D., “Development of New Al2O3/TiO2 Reinforced Glass-Ionomer Cements (GICs) Nano-Composites”, Journal of Basic Applcation of Science and Research, Vol. 8, pp. 7526-7529, 2012.
30. Gu, Y.W., Yap, A.U.J., Cheang, P. and Kumar, R., “Spheroidization of Glass Powders for Glass Ionomer cements”, Biomaterials, Vol. 25 pp. 4029–4035, 2004.
31. Lucas, M.E., Arita, K. and Nishino, M., ''Toughness, Bonding and Fluoride Release Properties of Hydroxyapatite-Added Glass Ionomer Cement'', Biomaterials, Vol. 24, pp. 3787–3794, 2003.
32. Upadhya, P.N. and Kishore, G., “GlassIonomer Cement The Different Generations”, Trends in Biomaterials Artificial Organs, Vol. 18, pp. 158-165, 2005.
33. Culberston, B.M., “Glass-Ionomer Dental Restoratives”, Progress in Polymer Science, Vol. 26, pp. 577-604, 2001.
34. Bertolini, M.J., Zaghete, M.A., Gimenes, R., Padovani, G.C. and Cruz, C.A.S., “Preparation and Evaluation of an Experimental Luting Glass Ionomer Cement to be Used in Dentistry”, Journal of Materials Science: Materials in Medicine, Vol. 20, pp. 1781-1785, 2009.
35. Ansari, S.M., Moshaverinia, Roohpour, N., Chee, W.W.L., Schricker, S.R. and Moshaverinia, A., “Properties of a Proline-Containing Glass Ionomer Dental Cement”, The Journal of Prosthetic Dentistry, Vol. 110, pp. 409-413, 2013.
36. Ana, I.D., Matsuya, S., Ohta, M. and Ishikawa, K., “Effects of Added Bioactive glass on the Setting and Mechanical Properties of Resin-Modified Glass Ionomer Cement”, Biomaterials, Vol. 24, pp. 3061–3067, 2003.
37. Xie, D., Brantley, W.A., Culbertsonb, B.M. and Wang, G., “Mechanical Properties and Microstructures of Glass-Ionomer Cements”, Dental Materials, Vol. 16, pp. 129–138, 2000.
38. Prentice, L.H., Tyas, M.J. and Burrow, M.F., “The Effect of Particle Size Distribution on an Experimental Glass Ionomer Cement”, Dental Materials, Vol. 21, pp. 505-510, 2005.
Journal of Advanced Materials in Engineering (Esteghlal)
Volume 35, Issue 2
September 2016
Pages 131-144

Files

Share

How to cite

Statistics

ارتقاء امنیت وب با وف ایرانی