مواد پیشرفته در مهندسی

مواد پیشرفته در مهندسی

بهینه‌سازی متغیرهای روکش‌کاری لیزری فولاد زنگ‌نزن سوپر دوپلکس با استفاده از روش سطح پاسخ

نوع مقاله : مقاله پژوهشی

نویسندگان
1 گروه مهندسی مواد و متالورژی، دانشکده مهندسی، دانشگاه فردوسی مشهد، مشهد، ایران
2 گروه مهندسی مکانیک، دانشکده مهندسی، دانشگاه فردوسی مشهد، مشهد، ایران
چکیده
مقدمه و اهداف: در این پژوهش، روکش‌کاری لیزری فولاد زنگ‌نزن سوپر دوپلکس 2507 روی فولاد کم‌آلیاژ 4130 مورد بررسی قرار گرفت و با هدف بررسی اثر توان لیزر، سرعت روبش و نرخ تغذیه پودر بر هندسه پوشش و میزان آستنیت و یافتن بهترین نمونه تک‌پاس انجام شد.
مواد و روش‌ها: متغیرهای مستقل شامل توان لیزر، سرعت روبش و نرخ تغذیه پودر و پاسخ‌ها شامل عرض، ارتفاع، عمق، زاویه ترشوندگی، رقت و مقدار آستنیت بودند. آزمایش‌ها بر اساس روش تحلیل سطح پاسخ، انجام و مدل پیش‌بینی برازش متغیرهای فرآیند ایجاد شد.
یافته‌ها: بهترین نمونه تک‌پاس در توان 1450 وات، نرخ تغذیه پودر 16/7 گرم بر دقیقه و سرعت روبش لیزر 4/2 میلی‌متر بر ثانیه می‌باشد.
نتیجه‌گیری: عرض روکش با افزایش توان و کاهش سرعت روبش، افزایش می‌یابد. ارتفاع روکش با افزایش نرخ تغذیه پودر در سرعت‌های پایین روبش، افزایش و در سرعت‌های بالای روبش کاهش می‌یابد. با کاهش سرعت روبش، ارتفاع افزایش می‌یابد. با افزایش توان و سرعت روبش و کاهش نرخ تغذیه، درصد رقت زیاد می‌شود. با افزایش سرعت روبش و کاهش توان، زاویه ترشوندگی کاهش می‌یابد. در سرعت‌های کم روبش با افزایش نرخ تغذیه، زاویه ترشوندگی افزایش می‌یابد. آستنیت با افزایش توان و کاهش سرعت روبش افزایش می‌یابد. آستنیت موجود شامل مرز‌دانه‌ای، ویدمنشتاتن و آستنیت درون‌دانه‌ای است. افزایش توان، فاصله بین بازوهای دندریتی ثانویه (λ2) را افزایش می‌دهد. صحه‌گذاری نتایج انجام شد و بیشترین درصد اختلاف، سه درصد است.
کلیدواژه‌ها
موضوعات

عنوان مقاله English

Parameter Optimization of Laser Cladding of Super Duplex Stainless Steel by Response Surface Methodology

نویسندگان English

Ali Jafari Moghaddam 1
Abolfazl Babakhani 1
Seyed Abdolkarim Sajjadi 1
Mohammad Hossein Farshidianfar 2
Ghasem Barati Darband 1
1 Department of Materials and Metallurgical Engineering, Faculty of Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
2 Department of Mechanical Engineering, Faculty of Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
چکیده English

Introduction and Objectives: In this study, laser cladding of 2507 super duplex stainless steel on 4130 low-alloy steel was investigated to examine the effects of laser power, scanning speed, and powder feed rate on coating geometry and austenite content, and to identify the optimal single-pass sample.
Materials and Methods: The independent variables including laser power, scanning speed, and powder feed rate, while the responses comprised width, height, depth, wetting angle, dilution, and austenite content. Experiments were conducted using the response surface methodology, and a predictive model was developed by fitting the process variables.
Results: The best single-pass sample is achieved with a power of 1450 W, a powder feed rate of 16.7 g/min, and a laser scanning speed of 4.2 mm/s.
Conclusion: Clad width increases with higher power and lower scanning speed. Clad height increases with a higher powder feed rate at low scanning speeds, whereas it decreases at high scanning speeds. Reducing the scanning speed leads to an increase in height. Dilution percentage rises with increased power and scanning speed, and with a reduced feed rate. The wetting angle decreases as scanning speed increases and power decreases; however, at low scanning speeds, the wetting angle increases with a higher feed rate. The austenite content increases with higher power and lower scanning speed. The observed austenite includes grain boundary, Widmanstätten, and intragranular austenite. Increasing the power results in a larger secondary dendrite arm spacing (λ2). The results were validated, showing a maximum discrepancy of 3%.

کلیدواژه‌ها English

Laser cladding
Single pass
2507 super duplex stainless steel
4130 low-alloy steel
Response surface methodology
1. Chao Q, Cruz V, Thomas S, Birbilis N, Collins P, Taylor A, et al. On the enhanced corrosion resistance of a selective laser melted austenitic stainless steel. Scr Mater. 2017;141:94-98. https://doi.org/10.1016/j.scriptamat.2017.07.037
2. Zhang Y, Qiu C, Chen Y, Yu J, Zhou J, Li L, et al. Influence of high‐frequency micro‐forging on microstructure and properties of 304 stainless steel fabricated by laser rapid prototyping. Steel Res Int. 2013;84(9):870–877. https://doi.org/10.1002/srin.201200259
3. Khan H, Zhang N, Zhu Zh, Jiang D, Asif T, Xu H. Behavior and susceptibility to stress corrosion cracking of a nickel‐based alloy in superheated steam and supercritical water. Mater Corros. 2019;70(1):48–56. https://doi.org/10.1002/maco.201810237
4. Li W, Xu P, Wang Y, Zou Y, Gong H, Lu F. Laser synthesis and microstructure of micro-and nano-structured WC reinforced Co-based cladding layers on titanium alloy. J Alloys Compd. 2018;749:10–22. https://doi.org/10.1016/j.jallcom.2018.03.235
5. Baldridge T, Poling G, Foroozmehr E, Kovacevic R, Metz T, Kadekar V, et al. Laser cladding of Inconel 690 on Inconel 600 superalloy for corrosion protection in nuclear applications. Opt Lasers Eng. 2013;51(2):180–184. https://doi.org/10.1016/j.optlaseng.2012.08.006 
6. Núñez Y, Mafra M, Morales RE, Borges PC, Pintaude G. The effect of plasma nitriding on the synergism between wear and corrosion of SAF 2205 duplex stainless steel. Indust Lubr Tribol. 2020;72(9):1117–1122. https://doi.org/10.1108/ilt-08-2019-0302
7. Zhou Y, Engelberg DL. Fast testing of ambient temperature pitting corrosion in type 2205 duplex stainless steel by bipolar electrochemistry experiments. Electrochem Commun. 2020;117:106779. https://doi.org/10.1016/j.elecom.2020.106779
8. Manvatkar V, De A, DebRoy T. Heat transfer and material flow during laser assisted multi-layer additive manufacturing. J Appl Phys. 2014;116(12):124905-124908. https://doi.org/10.1063/1.4896751
9. Boes J, Röttger A, Becker L, Theisen W. Processing of gas-nitrided AISI 316L steel powder by laser powder bed fusion–Microstructure and properties. Addit Manuf. 2019;30:100836. https://doi.org/10.1016/j.addma.2019.100836
10. Gu D, Chen H. Selective laser melting of high strength and toughness stainless steel parts: The roles of laser hatch style and part placement strategy.  Mater Sci Eng A 2018;725:419–427. https://doi.org/10.1016/j.msea.2018.04.046
11. Qiu C, Kindi MA, Aladawi AS, Hatmi LA. A comprehensive study on microstructure and tensile behaviour of a selectively laser melted stainless steel. Sci Rep. 2018;8:7785. https://doi.org/10.1038/s41598-018-26136-7
12. Papula S, Song M, Pateras A, Chen XB, Brandt M, Easton MA, et al. Selective laser melting of duplex stainless steel 2205: effect of post-processing heat treatment on microstructure, mechanical properties, and corrosion resistance. Materials 2019;12(15):2468. https://doi.org/10.3390/ma12152468
13. Geenen K, Röttger A, and Theisen W. Corrosion behavior of 316L austenitic steel processed by selective laser melting, hot‐isostatic pressing and casting. Mater Corros. 2017;68(7):764–775. https://doi.org/10.1002/maco.201609210
14. Casati R, Lemke J, Vedani M. Microstructure and fracture behavior of 316L austenitic stainless steel produced by selective laser melting.  J Mater Sci Technol. 2016;32(8):738–744. https://doi.org/10.1016/j.jmst.2016.06.016
15. Bahl S, Mishra S, Yazar KU, Kola IR, Chatterjee K, Suwas S. Non-equilibrium microstructure, crystallographic texture and morphological texture synergistically result in unusual mechanical properties of 3D printed 316L stainless steel. Addit Manuf. 2019;28:65–77. https://doi.org/10.1016/j.addma.2019.04.016
16. DebRoy T, Wei HL, Zuback JS, Mukherjee T, Elmer JW, Milewski JO, et al. Additive manufacturing of metallic components–process, structure and properties. Prog Mater Sci. 2018;92:112–224. https://doi.org/10.1016/j.pmatsci.2017.10.001
17. Pardo A, Merino MC, Coy AE,Viejo F, Arrabal R, Matykina E. Pitting corrosion behaviour of austenitic stainless steels–combining effects of Mn and Mo additions. Corros Sci. 2008;50(6):1796–1806. https://doi.org/10.1016/j.corsci.2008.04.005
18. Liu E, Huang F, Bao F, Xue Y, Wang H, Jin Y. Microstructure and electrochemical corrosion behaviors of laser‐cladded 2205 duplex stainless steel. Steel Res Int. 2020;91(6):1900456. https://doi.org/10.1002/srin.201900456
19. Huang F, Liu E, Qin Y, Wang Q, Jin Y, Wen L, et al.  Study of multi-pass laser-cladding 2205 duplex stainless steel coating: microstructure, electrochemical corrosion behavior, and wear-resistance properties. Coatings 2022;12(2):229. https://doi.org/10.3390/coatings12020229
20. Iams A, Keist J, Palmer T. Formation of austenite in additively manufactured and post-processed duplex stainless steel alloys. Metall Mater Trans A Phys Metall Mater Sci. 2020;51(2):982–999. https://doi.org/10.1007/s11661-019-05562-w
21. Jiang D, Gao X, Zhu Y, Hutchinson C, Huang A. In-situ duplex structure formation and high tensile strength of super duplex stainless steel produced by directed laser deposition. Mater Sci Eng A Struct Mater. 2022;833:142557. https://doi.org/10.1016/j.msea.2021.142557
22. Zhang Z, Kong F, Kovacevic R. Laser hot-wire cladding of Co-Cr-W metal cored wire. Opt Lasers Eng. 2020;128:105998. https://doi.org/10.1016/j.optlaseng.2019.105998
23. Mostajeran A, Shoja-Razavi R, Hadi R, Erfanmanesh M, Barekat M, Firouzabadi M. Evaluation of the mechanical properties of WC-FeAl composite coating fabricated by laser cladding method. Int J Refract Metals Hard Mater. 2020;88:105199. https://doi.org/10.1016/j.ijrmhm.2020.105199
24. Gowtham A, Chaitanya G, Katiyar JK, Chandak A, Gupta TVK. Experimental investigations on laser cladding of NiCrBSi + WC coating on SS410. Mater Today Proc. 2020;27:1984–1989. https://doi.org/10.1016/j.matpr.2019.09.044
25. Yao J, Zhang J, Wu G, Wang L, Zhang Q, Liu R. Microstructure and wear resistance of laser cladded composite coatings prepared from pre-alloyed WC-NiCrMo powder with different laser spots. Opt Laser Technol. 2018;101:520–530. https://doi.org/10.1016/j.optlastec.2017.12.007
26. Khamidullin B, Tsivilskiy IV, Gorunov AI, Gilmutdinov AKh. Modeling of the effect of powder parameters on laser cladding using coaxial nozzle. Surf Coat Technol. 2019;364:430–443. https://doi.org/10.1016/j.surfcoat.2018.12.002
27. Cheikh HEl, Courant B, Branchu S, Hascoët J-Y, Guillén R. Analysis and prediction of single laser tracks geometrical characteristics in coaxial laser cladding process. Opt Lasers Eng. 2012;50(3):413–422. https://doi.org/10.1016/j.optlaseng.2011.10.014
28. Reddy L, Preston SP, Shipway PH, Davis C, Hussain T. Process parameter optimisation of laser clad iron based alloy: Predictive models of deposition efficiency, porosity and dilution. Surf Coat Technol. 2018;349:198–207. https://doi.org/10.1016/j.surfcoat.2018.05.054
29. Lei K, Qin X, Liu H, Ni M. Analysis and modeling of melt pool morphology for high power diode laser cladding with a rectangle beam spot. Opt Lasers Eng. 2018;110:89–99. https://doi.org/10.1016/j.optlaseng.2018.05.022
30. Fan P, Zhang G. Study on process optimization of WC-Co50 cermet composite coating by laser cladding. Int J Refract Metals Hard Mater. 2020;87:105133. https://doi.org/10.1016/j.ijrmhm.2019.105133
31. Erfanmanesh M, Abdollah-Pour H, Mohammadian-Semnani H, Shoja-Razavi R. An empirical-statistical model for laser cladding of WC-12Co powder on AISI 321 stainless steel. Opt Laser Technol. 2017;97:180–186. https://doi.org/10.1016/j.optlastec.2017.06.026
32. Nabhani M, Razavi RS, Barekat M. An empirical-statistical model for laser cladding of Ti-6Al-4V powder on Ti-6Al-4V substrate. Opt Laser Technol. 2018,100:265–271. https://doi.org/10.1016/j.optlastec.2017.10.015
33. Aghili S, Shamanian M. Investigation of powder fed laser cladding of NiCr-chromium carbides single-tracks on titanium aluminide substrate. Opt Laser Technol. 2019;119:105652. https://doi.org/10.1016/j.optlastec.2019.105652
34. Wu Z, Li T, Li Q, Shi B, Li X, Wang X, et al. Process optimization of laser cladding Ni60A alloy coating in remanufacturing. Opt Laser Technol. 2019;120:105718. https://doi.org/10.1016/j.optlastec.2019.105718
35. Shi Y, Li Y, Liu J, Yuan Z. Investigation on the parameter optimization and performance of laser cladding a gradient composite coating by a mixed powder of Co50 and Ni/WC on 20CrMnTi low carbon alloy steel. Opt Laser Technol. 2018;99:256–270. https://doi.org/10.1016/j.optlastec.2017.09.010
36. Singh J, Thakur L, Angra S. An investigation on the parameter optimization and abrasive wear behaviour of nanostructured WC-10Co-4Cr TIG weld cladding. Surf Coat Technol. 2020;386:125474. https://doi.org/10.1016/j.surfcoat.2020.125474
37. Aggarwal K, Urbanic R, Aggarwal L. A methodology for investigating and modelling laser clad bead geometry and process parameter relationships. SAE Int J Mater Manu. 2014;7(2):269–279. https://doi.org/10.4271/2014-01-0737
38. Khorram A, Davoodi Jamaloei A, Paidar M, Cao X. Laser cladding of Inconel 718 with 75Cr3C2+ 25 (80Ni20Cr) powder: Statistical modeling and optimization. Surf Coat Technol. 2019;378:124933. https://doi.org/10.1016/j.surfcoat.2019.124933
39. Palmer T, Elmer J, Wong J. In situ observations of ferrite–austenite transformations in duplex stainless steel weldments using synchrotron radiation. Sci Technol Weld Join. 2002;7(3):159–171. https://doi.org/10.1179/136217102225004194
40. Palmer T, Elmer J, Babu S. Observations of ferrite/austenite transformations in the heat affected zone of 2205 duplex stainless steel spot welds using time resolved X-ray diffraction. Mater Sci Eng A 2004;374(1-2):307–321. https://doi.org/10.1016/j.msea.2004.03.037
41. Alvarez-Armas I, Degallaix-Moreuil S, editors. Duplex stainless steels. Hoboken (NJ): John Wiley & Sons; 2013. https://doi.org/10.1002/9781118557990
42. Zhang Z, Jing H, Xu L, Han Y, Li G, Zhao L. Investigation on microstructure and impact toughness of different zones in duplex stainless steel welding joint. J Mater Eng Perform. 2017;26(1):134–150. https://doi.org/10.1007/s11665-016-2441-5
43. Karlsson L, Börjesson J. Orientation relationships of intragranular austenite in duplex stainless steel weld metals. Sci Technol Weld Join. 2014;19(4):318–323. https://doi.org/10.1179/1362171813y.0000000192
44. Saeidi K, Kevetkova L, Lofaj F, Shen Z. Novel ferritic stainless steel formed by laser melting from duplex stainless steel powder with advanced mechanical properties and high ductility. Mater Sci Eng A 2016;665:59–65. https://doi.org/10.1016/j.msea.2016.04.027
45. Saeidi K, Alvi S, Lofaj F, Petkov VI, Akhtar F. Advanced mechanical strength in post heat treated SLM 2507 at room and high temperature promoted by hard/ductile sigma precipitates. Metals 2019;9(2):199. https://doi.org/10.3390/met9020199
46. Jiang D, Birbilis N, Hutchinson CR, Brameld M. On the microstructure and electrochemical properties of additively manufactured duplex stainless steels produced using laser-powder bed fusion. Corrosion 2020;76(9):871–883. https://doi.org/10.5006/3571
47. Kou S. Welding metallurgy. 3rd ed. Wiley; 2020.
48. Barekat M, Razavi RS, Ghasemi A. Nd: YAG laser cladding of Co–Cr–Mo alloy on γ-TiAl substrate. Opt Laser Technol. 2016;80:145–152. https://doi.org/10.1016/j.optlastec.2016.01.003
49. Jelvani S, Shoja-Razavi R, Barekat M, Dehnavi M. Empirical-statistical modeling and prediction of geometric characteristics for laser-aided direct metal deposition of Inconel 718 superalloy. Met Mater Int. 2020;26(5):668–681. https://doi.org/10.1007/s12540-019-00355-7
50. Toyserkani E, Khajepour A, Corbin SF. Laser cladding. Boca Raton (FL): CRC Press; 2005. https://doi.org/10.1201/9781420039177
51. Jouvard JM, Grevey DF, Lemoine F, Vannes AB. Continuous wave Nd: YAG laser cladding modeling: a physical study of track creation during low power processing. J Laser Appl. 1997;9(1):43–50. https://doi.org/10.2351/1.4745444
52. de Oliveira U, Ocelík V, De Hosson JThM. Analysis of coaxial laser cladding processing conditions. Surf Coat Technol. 2005;197(2-3):127–136. https://doi.org/10.1016/j.surfcoat.2004.06.029
53. Zhao Y, Guan C, Chen L, Sun J, Yu T. Effect of process parameters on the cladding track geometry fabricated by laser cladding. Optik (Stuttg). 2020;223:165447. https://doi.org/10.1016/j.ijleo.2020.165447
54. Goodarzi DM, Pekkarinen J, Salminen A. Effect of process parameters in laser cladding on substrate melted areas and the substrate melted shape. J Laser Appl. 2015;27(S2):S29201. https://doi.org/10.2351/1.4906376
55. El Cheikh H, Courant B, Branchu S, Huang X, Hascoët JY, Guillén R. Direct laser fabrication process with coaxial powder projection of 316L steel. Geometrical characteristics and microstructure characterization of wall structures. Opt Lasers Eng. 2012;50(12):1779–1784. https://doi.org/10.1016/j.optlaseng.2012.07.002
56. Cui L, Zhang M, Guo SR, Cao YL, Zeng WH, Li X, et al. Multi-objective numerical simulation of geometrical characteristics of laser cladding of cobalt-based alloy based on response surface methodology. Meas Control 2021;54(7-8):1125–1135. https://doi.org/10.1177/0020294020944955
57. Davim JP, Oliveira C, Cardoso A. Predicting the geometric form of clad in laser cladding by powder using multiple regression analysis (MRA). Mater Des. 2008;29(2):554–557. https://doi.org/10.1016/j.matdes.2007.01.023
58. Ansari M, Razavi RS, Barekat M. An empirical-statistical model for coaxial laser cladding of NiCrAlY powder on Inconel 738 superalloy. Opt Laser Technol. 2016;86:136–144. https://doi.org/10.1016/j.optlastec.2016.06.014
59. Zhang J, Zhang Q, Chen Zh, Li D, Tong W, Yao J, et al. Experimental and statistical analyses of geometry characteristics of Inconel 718 laser clad layer with response surface methodology. J Laser Appl. 2019;31(3):032016. https://doi.org/10.2351/1.5098044
60. Javid Y. Multi-response optimization in laser cladding process of WC powder on Inconel 718. CIRP J Manuf Sci Technol. 2020;31:406–417. https://doi.org/10.1016/j.cirpj.2020.07.003
61. Lian G, Yao M, Zhang Y, Chen C. Analysis and prediction on geometric characteristics of multi-track overlapping laser cladding. Int J Adv Manu Technol. 2018;97(5):2397–2407. https://doi.org/10.1007/s00170-018-2107-6
 
 

تحت نظارت وف بومی